How to Laser Cut Leather & Fabric Without Burn or Fray

Leather and fabric are two of the most rewarding—and most misunderstood—materials for CO₂ lasers. New users often struggle with burnt edges, yellow smoke marks, fray, curling, uneven kerf, and inconsistent results.

Fortunately, these issues disappear once you understand their thermal behavior and airflow. This guide provides proven 2 mm leather and single-layer fabric cutting settings, lens recommendations, airflow strategies, fixing methods, and troubleshooting to help you achieve consistently clean, fray-free edges.

✅ Best for CO₂ lasers (60–150 W)
✅ Covers leather (2 mm) + fabric (single layer)
✅ Includes speed tables + lens + airflow + finishing tips
✅ Beginner-friendly + workshop-grade accuracy

Quick Answer

Leather and fabric both cut extremely well on a CO₂ laser—if the machine is set correctly:

  • Use a 50 mm lens
  • Use high speed to reduce burn
  • Use medium → low air assist depending on material
  • Secure the sheet so it doesn’t lift or flutter
  • Use honeycomb table + proper exhaust
Rule of thumb: Faster = Cleaner. Slow cutting causes overheating → yellow/burn marks.

Recommended Settings (Leather & Fabric)

These baseline settings come from real machine（Gweike M Series 6-in-1） tests with ~90% laser power utilization. Tune ±20% based on material thickness, tanning method, weave, and airflow.

Leather Cutting Settings (2 mm)

Power Best Speed Notes
60 W 35–40 mm/s Good for hobby cutting
100 W 45–50 mm/s Cleaner at same depth
150 W 60–65 mm/s Fastest + cleanest

Fabric Cutting Settings (Single Layer)

Power Best Speed Notes
60 W ~58 mm/s Good baseline
100 W ~98–100 mm/s Faster & cleaner
150 W ~150–200 mm/s For production
Tip: Higher speed = less burn. If underpowered, increase speed instead of lowering.

Why Leather & Fabric Burn/Fray

Leather contains organic collagen + tannins; fabric fibers (cotton, polyester, felt) have different melting points. When energy density is too high (slow movement), fibers carbonize → burned edge.

For fabric, the laser cuts as it melts the edge. → That molten edge “seals” the fibers → no fray.

So the secret is:

High speed → less heat → clean sealed edge

Lens & Focus Setup

Thickness Lens Reason
≤2 mm 50 mm Sharp spot + clean kerf
Fabric (thin) 50 mm (slight defocus) Reduce overheat

Best practice: Focus exactly on the top surface. For delicate fabrics: defocus 0.3–0.5 mm upward to soften edge heat.

Air Assist Strategy

Air affects both cut quality and material stability.

  • Leather → Medium air
  • Fabric → Low air (too much → flutter)
  • Side-angled flow preferred over strong vertical
Too much air = Blowout + flutter → fray/warp

Work Bed Choice (Honeycomb Wins)

  • Always use honeycomb bed
  • Allows bottom airflow
  • Reduces char reflection
  • Prevents back-burn marks

Never cut leather/fabric directly on a metal plate— → heat bounce marks + trapped smoke.

Shop Honeycomb Tables Upgrade Air Assist

Securing Leather & Fabric

Loose pieces → blow up → scorch + inaccurate kerf.

  • Masking tape edges
  • Weigh down corners
  • Acrylic frame hold-down
  • Mild adhesive spray (fabric only)

Cutting SOP (Step-by-Step)

  1. Install 50 mm lens
  2. Place sheet on honeycomb bed
  3. Fix edges (tape/weights)
  4. Set baseline speed from tables
  5. Use medium-low air assist
  6. Run small test pattern
  7. Adjust speed upward if edges burn

Leather Cutting Tips

  • Vegetable-tanned leather cuts cleaner than chrome-tanned
  • Masking film reduces smoke stain
  • Wipe edges with alcohol afterward
  • Higher speed → less discoloration
  • Saddle soap helps finishing

Fabric Cutting Tips

  • Polyester cuts best → sealed clean edge
  • Cotton frays → finish with edge-sealing fluid
  • Use low air to avoid flutter
  • Use fabric stiffener for soft fabrics
  • Keep fabric tensioned → clean cutlines

Troubleshooting

Issue Cause Fix
Burn marks Too slow Increase speed
Fray Fabric loose Tape / weights / frame
Wrinkling Air too strong Lower air
Dark sticky edge Overheat Faster speed
Backside marks No honeycomb airflow Use honeycomb bed

Cleaning & Finishing

Leather

  • Alcohol wipe for odor & soot
  • Saddle soap or Tokonole for clean edge
  • Light burnish if needed

Fabric

  • Trim stray fibers
  • Heat-seal tools for cotton
  • Masking protects surface design

Safety Notes

  • Leather fumes → must ventilate
  • Never cut unknown coated fabrics
  • Filter + exhaust recommended
  • Do not leave unattended

FAQ

Q: Can a 60 W CO₂ laser cut leather?
Yes, 2 mm leather cuts well at 35–40 mm/s.

Q: Why does my leather edge look yellow?
Speed is too low; increase speed for cleaner edge.

Q: Does fabric always seal cleanly?
Polyester: yes. Cotton: may require post-sealing.

Q: Is masking tape helpful?
Yes — reduces smoke stain.

Conclusion

Leather and fabric are easy to cut on CO₂ lasers once you understand the basics:

  • Use fast speeds
  • Use 50 mm lens
  • Use medium-low airflow
  • Secure the sheet
  • Use honeycomb bed

Start with the recommended settings, then fine-tune for your specific tanning/weave style.

Shop Leather & Fabric Material Kits Browse CO₂ Laser Cutting Machines
ブログに戻る